Wisconsin-Minnesota Contractor Services Insulation, Spray Foam, and Drywall Services

OUR SERVICE PROCESS PROCEDURES

Step 1. GBI goes the extra mile to determine the whole house service needs and makes recommendations based upon your specific needs. In doing so, we inform you about the benefits and application of our products so that you'll be well informed; so that you will want to inform and recommend us to your friends.

Step 2. GBI spends the extra time to prepare the job site for spray operations by masking all windows, doors, fixtures, etc. then, if needed, we remove old material and install appropriate vent baffles.

Step 3. GBI briefs our Factory Trained Staff prior to each spray operation commencement. We set the high tech equipment to material specs using our pre-application checklist. We comply with all safety standards. We apply appropriate spray materials; and throughout the entire process, we display our craftsmanship, golden rule customer service, and pride in mission "well done".

Step 4. GBI spends extra time cleaning up debris, our equipment, removing all prep material, scraping the studs, and leaving a flush surface for Drywall or other wall covering installation.

Step 5. GBI makes a final inspection with a third party Home Performce with Energy Star certified consultant to confirm that all areas have been addressed, insulated properly and that all the clean up is 100% complete. We leave you totally satisfied; knowing that your habitat is cleaner and greener. Green Builder Insulation LLC is a Friend to YOU / Friendly to OUR Planet.

Home Performance Testing with a Wisconsin "Focus On Energy" Consultant

Before and After

Spray Foam Insulation with DEMILEC USA Spray Foam

Best Quality Spray Foam Technology applied by Factory Trained Applicators.using the Highest Quality Equipment available.

Complete Whole Building Air Sealing

Including Attics, Crawl Spaces, Cantilevered Structures, Box Sills, Cathedral Ceiling, Exterior & Interior walls, Knee walls, duct work,

vent piping, and all the almost undetecable cracks and openings. Again, we utilize "Focus On Energy Consultant Testing before and after.

Proper Vented Attics

Plus sales, service, and installation of Energy Star exhaust fans and bathroom fans

Proper Non Vented Attics and Crawlspaces Complete SealingAir Tight Sealing with the Best Building Science Technology

Injection Foam Insulation into existing home exterior walls

Removal of some siding to drill holes and inject foam into walls without removing exterior or interior walls. Wall cavities are completely filled and sealed and plugs are placed into drilled holes and sealed; then, the original siding is replaced onto the wall.

Insulation Removal

Out with the old failing insulation, replaced with the lastest in insulation technology.

Sound Proof / Reduction Insulation

in Theater Rooms , Children Play Rooms, Home Offices, Music Rooms, and Interior Walls and Floors

Drywall Services

Professionally finished drywall and taping done to your satisfaction

Listen to You

Whether your project is unique or ordinary; we will go the extra mile, and spend the extra time to work with you on mission completion.

As you browse our site you will see the pride in our craftsmanship and tidiness. In fact, our customer friends often comment that our job sites are cleaner and greener when we leave than when we arrived. We send our factory trained and certified staff to continuing education classes on spray foam insulation, spray coatings, building envelope science and environmental practices; so that we continue our dedication to our mission of sharing and applying our Green Builder Insulation

Friend to YOU / Friendly to OUR Planet

OUR SERVICE FOR EXISTING WALLS

Demilec "Pour-In-Place" is a ½ pound, open cell slow rising foam that can be injected into an existing wall empty wall cavity. Our process starts by inspecting the existing wall with infrared camera, snake camera, stud finders, and fish tapes to determine what obstructions that may impede the cavity fill. We are looking for wiring, window weights and possible horizontal supports blocking the foam from filling the cavity.

Our next step is to drill holes in the existing walls between the studs to fill the cavities. We typically drill 3 holes per stud cavity with ¾” holes. This can very depending on what we discover in the wall. Due to the small size of the holes, repairing them is usually not a problem for the handy homeowner or handyman repairman.

We then inject the foam into each cavity with a special tool attached to our spray gun. This spray foam insulation is a slow process; compared to an open cavity spray foam application. The technique should be performed by a trained applicator technician. We like to give it a chance to fill every crack and hole in the wall. As we are filling the cavity we also check with an infrared camera to determine that we are filling this hidden cavity with foam.

The skilled applicator uses a towel to keep the foam from coming out the lower holes; until he fills the very top hole. We let the foam expand out of this top hole to ensure we have filled completely to the top cap. We use lots of card board and plastic to protect the home and furniture. And, we clean this up and take it away after mission completion. We intend to leave our work site cleaner and greener than when we arrived.

And, if the condition of your building permits; we can do the same process on the exterior; which is more conducive to keeping your interior cleaner and with less inconvenience to you during application. Depending on the siding, accessibility, etc. it is usually preferred method for applying foam to existing walls.